wires

  1. Strymon DC Power Cables for Effect Pedals and Such...
    Sold

    For sale Strymon DC Power Cables for Effect Pedals and Such...

    I got me Strymon DC power cables of the sort that comes with Zuma and Ojai purchases. Funny that, because that is where I got these. I have twenty five (25) 18" and five (5) 36" that I am selling for $2 per cable. I also have four (4) 20" cables that are not Strymon, but I couldn't tell you who...
    $2.00
  2. Discount Bassy

    SOLD Strymon DC Power Cables for Effect Pedals and Such...

    I got me Strymon DC power cables of the sort that comes with Zuma and Ojai purchases. Funny that, because that is where I got these. I have twenty five (25) 18" and five (5) 36" that I am selling for $2 per cable. I also have four (4) 20" cables that are not Strymon, but I couldn't tell you who...
  3. Wangus67

    Is It Possible To Have Fried Wiring In The Cab?

    Hey All- This may be a totally noob kinda question, but here's the situation: I acquired a Fender Bassman 1x15 cab and had always assumed that the speaker had fried (due to the fried sound). It is a JBL D-130F 8 ohm that had been re-coned. Well I just bought a used Peavey Black Widow 1505-8...
  4. RumbleMan3

    Crackling questions... Trying to find the cause!!

    Hey guys! (Not sure if this is the right forum to post this in, but anyway) I am experiencing some crackling... u know the type, when you’re messing around with your loose cables and stuff. Not feedback, just little pops and crackles. Here and there, it keeps coming up, ever since I...
  5. M

    Need info about these wires

    I need to know what type of wire can I take to replace these ones: Can you please give me some info about them? Thanks!
  6. A

    Buzzing Amplifier Problems

    Hello everyone. I just made an account to post this issue that we can't seem to figure out. Our bassist uses a Peavey TNT 150 combo (inb4 get a better amp obvi). At some point the amp started buzzing. A quick check led me to believe the speaker blew (compressor light stays on constantly, old...
  7. rodv66

    Wires?

    I'm repainting a bass and took the precision pickups out, and sodder connections from pots broke off. There is a black and white one, no suprise, but there is no wire for connecting the two pieces together. Can i just sodder one wire to each of the spit coils?
  8. 20180504_203521

    20180504_203521

    3 wires red, black, green and the shield.
    • Mrmatt1972
    • Media item
    • wires
    • Comments: 0
    • Album: Wiring question
  9. mustBmtd

    'Do I Really Need Original Ground Wires'

    Dropping a Flexcore 4band Preamp in my Lakland 55-01. Preamp has a ground slot to screw into. So if you know about the 55-01, it already has a screwed in ground wire in each pickup cavity. So my question is based on if I really need to use those. Since my pickup ground wires will be screwed into...
  10. Matthew_84

    Wiring from Blend Pot to Barrel Jack

    Hey guys, I am going to remove the preamp from my bass and just run the wiring straight from the blend pot to the barrel jack. There will be zero tone or volume pots in this configuration. My barrel jack has three lugs. The two in the front "Lug A" and "Lug B" currently have nothing wired to...
  11. Spectre Gunner

    Complete Squire Makeover - Is shielded wire really necessary here?

    I'm in the process of giving a Squire Affinity P Bass Fretless a complete makeover. When I'm done with this, only the body and defretted neck will be original Squire Affinity. I want to see how much better and how far I can take this bass to a higher level. I"ll have my pro luthier set it up...
  12. Fender_Bender

    Protecting 51 P style pup exposed wires?

    Hey all. Most know I bought a single coil P bass last week and I’m wondering about a way to protect the exposed wires going from the left and right side of the pup to the flatwork. I have several ideas that could work such as silicone caulking or epoxy but am wondering if this is a bad idea or...
  13. NoiseNinja

    Which wires to conect to which pins on a 6 pin on/off switch?

    Monday I am ordering a Seymour Duncan Rickenbacker replacement neck pickup I plan to install in my Ibanez Mikro bass in the far neck position (connected in standard humbucker series mode. Will have to carve an extra cavity for this) where I already have a pair of P/J EMG Geezer Butler pickups...
  14. W

    Double Bass Accessory Needed to Hold Pickup Wires / Wireless Input

    Hi there. I have a pickup on my double bass's bridge, and currently have 'dangling wires' when I plug my (wireless) input into my pickups. I am seeking some type of bag, or satchel, if you will, to hold my wireless input, similar to this image.
  15. Aloe

    The best way to route multiple wires to a jack

    Hi, I've got an open-type stereo jack for replacement and I have 6 wires that come to ground. Ground from bridge, grounds from volume pots, ground from EQ pots, shield, ground from preamp. And that's quite a mess soldering all them to the one contact hole, I always end up soldering some wires...
  16. Finnigan's wake

    3 wires Humbucker wiring, i need help

    I'm working on my Fenix bass, it has a humbucker with RED-WHITE-BLACK-BARE wires. Actually is connected to a SPDT for the coil splitting, i want to wire it in a DPDT switch to add the series/parallel position. the red wire is soldered to the first lug, the white to the third, black&bare...
  17. NoiseNinja

    How to wire the HPF/LPF active preamp circuit from my Aria Pro II Laser Electric Classic?

    So I decided to gut my Aria Pro II Laser Electric Classic for it's active circuit, an active high pass filter and low pass filter run on 18V controlled by one tone knob with a mid position lock. The reason is that I now use my Aria Pro II strung and set up as a 4 string baritone slide guitar...
Top Bottom
Back